Bevel Gloss White

It can be challenging to order the right amount of tiles for a project because there may be difficult cuts that lead to breakages or tiles that are not suitable for use. As a general rule, it is recommended to order 10% extra for cutting and waste. However, for smaller areas with large tiles, the wastage can be higher than 10%. To ensure that you have enough tiles for your project, it can be helpful to draw out the space and calculate the exact number of tiles needed, then add 10% for cutting and waste. If you would like help estimating the number of tiles needed, you can talk to your installer or one of our team members. Please note that these are only estimates and we cannot be held responsible for over- or under-ordering due to circumstances that may arise during installation.

Proper planning is essential when starting a tiling project. It is important to consider all the necessary products for substrate preparation, including underfloor heating, uncoupling membranes, adhesive, profiles, tiles, grout, silicone, and sealants if needed. Our team is able to provide expert advice and guidance for all types of installations, and with our wide range of installation products, we can help you achieve a successful installation from start to finish.

It is generally a good idea to match the colour of the grout to the main colour of the tile to minimize its appearance. However, there are exceptions where you may want to use a contrasting grout colour to create a feature or highlight traditional tile patterns. Another factor to consider is the type of grout you use. Traditional cement-based grouts are durable but may fade over time, while epoxy grouts are more resistant to fading, retain their colour longer, and are waterproof, making them ideal for high traffic and wet areas. Ultimately, the decision of what colour and type of grout to use will depend on your personal preference and the specific needs of your project.

For regular maintenance, it is best to use a high-quality pH-neutral cleaner, which is safe for use on all types of porcelain, ceramic, and natural stone tiles. To deep clean your floor, you can use an alkaline-based cleaning product, which can remove old wax treatments and stubborn stains and is suitable for basic cleaning on unpolished natural stones. Be sure to follow the manufacturer's instructions when using any cleaning product to ensure that it is used safely and effectively.

A 20-kilogram bag of tile adhesive typically covers an area of 3 to 5 square meters, depending on the surface being tiled. As a general guideline, a 20-kilogram bag will cover:

- 5 square meters when installing an anti-fracture membrane, waterproofing membrane, or tile backer board.
- 4 square meters when installing tiles on old concrete, surface levelled or wall surfaces.
- 3 square meters when installing tiles on an anti-fracture membrane.

The choice between standard and fast-set tile adhesive depends on a variety of factors, including the type of tile, the surface being tiled, and the conditions in which the tiling is being done.

Standard tile adhesive is a good choice for most tile installations, as it provides a strong bond and allows for some flexibility in the tile positioning. It's also suitable for large format tiles and porcelain. Typically standard setting adhesives are used for wall tiling where you might need a bit more time to work.

Fast-set tile adhesive, as the name implies, sets quickly and can be used when time is of the essence, or if the conditions are such that the tile must be set in a short period of time. Also, this type of adhesive can be used in extreme weather conditions where the standard adhesive may not set properly. However, they are often not suitable for large format tile (larger than 600x600mm) unless specified by the manufacturer or combined with additives to increase the flexibility.

Don't hesitate to contact us for advice on selecting the appropriate and cost-efficient tile adhesive for your project.

All tiles are produced by firing a clay. During this heating and cooling process, tiles will start to form some deviation over the surface. This is called bowing. The accepted EU standard for bowing is 0.5% over a given length. This does mean the centre of a tile edge can be higher than the corners. For example a 600mm edge can be 3mm higher in the centre than at the corners. This will create a high spot and low spot a the point of the brick bond joint.

Due to this nature of tile manufacturing, it is typically not recommended to overlap the grout joints and brick bond larger format tiles. If clients do want to overlap this joint, it is recommended to only overlap by 1/3 of the tile lengths and use a clip levelling system to minimise any impact.

Clip or tile levelling systems are used to help "bend" and "flex" a tile to ensure the edges and grout joints are aligned during installation. It acts as both a spacer and a method of levelling the tile surface. All tiles are subject to a deviation across their surface of 0.5% of the edge length, plus there is some inherent flexibility of the tile which can cause the tile to deform under force (either by the fitter or through shrinking of adhesive).

These levelling system are used for any tile installation (but more typically were lengths are 800mm or greater), and is a method of flexing the tile corners and centres to level the surface of the tile installation.